CABLE ROUTING
2-52
1. Meter assembly 2 coupler
2. Ignition coil sub-wire harness 2 coupler
3. Front wheel sensor coupler
4. Cylinder identification sensor coupler
5. Clutch hose
6. Wire harness
7. Accelerator position sensor coupler
8. Starter motor lead
9. Throttle position sensor coupler
10. Radiator fan motor sub-wire harness coupler
11. Air induction system solenoid coupler
12. Atmospheric pressure sensor coupler
13. Upper radiator inlet pipe
14. Intake funnel servo motor lead
15. Main switch leads
16. Throttle servo motor coupler
17. Thermostat outlet hose
18. Intake funnel servo motor coupler
19. SELECT/RESET button unit lead
20. Brake hose (front brake master cylinder to
hydraulic unit)
21. Meter assembly 1 lead
22. Throttle cables
23. Coolant reservoir breather hose
24. Thermostat inlet pipe (rear cylinders)
25. Crankcase breather hose
A. The ignition coil sub-wire harness 2 coupler, front
wheel sensor coupler, and cylinder identification
sensor coupler may be positioned in any order.
B. Route the clutch hose to the inside of ignition coil
sub-wire harness 2, front wheel sensor lead, and
cylinder identification sensor lead.
C. Insert the projection on the plastic band into the
hole in the wire harness mounting panel, and then
fasten the wire harness at the positioning tape with
the band.
D. Fasten the starter motor lead, ignition coil sub-wire
harness 2, front wheel sensor lead, and cylinder
identification sensor lead with a plastic locking tie.
Align the plastic locking tie with the positioning
tape on the starter motor lead.
E. Route the starter motor lead between the frame
and the leads (air induction system solenoid lead,
atmospheric pressure sensor lead, and radiator fan
motor sub-wire harness).
F. Make sure that the positioning tape on the radiator
fan motor sub-wire harness is higher than the front
frame as shown in the illustration.
G. Route the meter assembly 2 lead between the
main switch leads and the air filter case.
H. Route the intake funnel servo motor lead above
the sponge damper.
I.
Route the meter assembly 2 lead to the front of the
upper radiator inlet pipe, then to the rear of the
intake funnel servo motor lead.
J. Install the throttle servo motor coupler onto the
throttle servo motor coupler bracket so that the
coupler is positioned between the bracket and the
front frame.
K. Route the intake funnel servo motor lead between
the air filter case and the thermostat assembly, and
route the lead to the rear of thermostat outlet hose.
L. Fasten the intake funnel servo motor lead with the
holder on the right side of the air filter case.
M. Insert the projection on the intake funnel servo
motor coupler into the hole in the thermostat
housing bracket.
N. Route the throttle cables to the outside of the
brake hose (front brake master cylinder to
hydraulic unit) and SELECT/RESET button unit
lead.
O. Route the meter assembly 1 lead above the
throttle cables.
P. Install the coolant reservoir breather hose so that
the end of the hose is positioned as shown in the
illustration.
Q. When routing the crankcase breather hose make
sure that the hose is not pinched between the
thermostat inlet pipe (rear cylinders) and the front
frame or between the rear reed valve cover and the
front frame.
Summary of Contents for Vmax VMX17C 2009
