Yamaha F30 Page 60 Owner'S Manual Download

Page: 60 / 120

Operation

2. Turn the air vent screw clockwise to

close it.

3. Remove the fuel tank from the boat.
4. To loosen the air vent screw, turn it

counterclockwise until it stops.

5. While pressing and holding the pressure

relief tab under the fuel tank cap, slowly
turn the fuel tank cap counterclockwise
1/4 turn.

TIP:

Release the fuel vapor contained in the fuel
tank.
6. While pressing and holding the pressure

relief tab under the fuel tank cap again,
turn the fuel tank cap counterclockwise
to remove it.

7. Fill the fuel tank with fuel.

WARNING!

Do not overfill. Otherwise fuel can ex-
pand and overflow if the temperature
increases.

[EWM02611]

1. Fuel joint
2. Fuel hose

1. Air vent screw

ZMU07443

ZMU07444

ZMU07445

1. Pressure relief tab
2. Fuel tank cap

ZMU07446

ZMU07447

6BG-9-3F-E0.book 54 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands