Yamaha F30 Page 98 Owner'S Manual Download

Page: 98 / 120

Maintenance

sion from cavitation or ventilation, or other
damage.



Check the propeller shaft for damage.



Check the splines for wear or damage.



Check for fish line tangled around the pro-
peller shaft.



Check the propeller shaft oil seal for dam-
age.

EMU30663

Removing propeller

EMU29198

Spline models

1. Straighten the cotter pin and pull it out

using a pair of pliers.

2. Remove the propeller nut, washer, and

spacer (if equipped).

WARNING! Do

not use your hand to hold the propel-
ler when loosening the propeller nut.

[EWM01891]

3. Remove the propeller, washer (if

equipped), and thrust washer.

EMU30673

Installing propeller

EMU46121

Spline models

NOTICE

ECM00502

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

1. Apply Yamalube Marine Grease or a

corrosion resistant grease to the propel-
ler shaft.

2. Install the spacer (if equipped), thrust

washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01882]

3. Install the spacer (if equipped) and the

washer. Tighten the propeller nut to the
specified torque.

1. Cotter pin
2. Propeller nut
3. Washer

4. Spacer
5. Propeller
6. Thrust washer

6BG-9-3F-E0.book 92 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands