Yamaha F30 Page 108 Owner'S Manual Download

Page: 108 / 120

Trouble Recovery

102

If the water separator-alert indicator blinks,
perform the following procedure.

1. Stop the engine.
2. Remove the top cowling.
3. Remove the holder.

4. Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01951]

5. Unscrew the filter cup from the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01961]

6. Drain the water in the filter cup by soak-

ing it up with a rag.

7. Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01971]

8. Connect the water detection switch cou-

pler securely until a click is heard.

1. Water separator-alert indicator

1. Holder

ZMU05441

ZMU06424

1. Water detection switch coupler

1. Filter cup
2. Water detection switch lead

ZMU06425

ZMU06426

6BG-9-3F-E0.book 102 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands