Yamaha F30 Page 77 Owner'S Manual Download | Manualshive

Page: 77 / 120

background image

Operation

71

power trim and tilt unit or in the pow-
er tilt unit loses pressure.

[EWM00263]

NOTICE:

Do not use the tilt support

lever or knob when trailering the
boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 75.

[ECM01642]

EMU34481

Procedure for tilting down (hydro tilt
models)

1. Release the tilt lock lever.

2. Hold the rear of the top cowling with one

hand, tilt the outboard motor up slightly
and pull out the tilt support knob or re-
turn the tilt support lever.

3. Slowly tilt the outboard motor down.
4. Place the tilt lock lever in the lock posi-

tion.

EMU44601

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support knob
becomes free.

2. Pull out the tilt support knob.

ZMU06396

ZMU06412

ZMU06408

ZMU06404

ZMU06408

6BG-9-3F-E0.book 71 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
75
76
77
78
79
...
»

Summary of Contents for F30

























































































































Reviews:

No comments

Related manuals for F30

Brand: Yamaha Pages: 86

Brand: MSI Pages: 112

Brand: Gigabyte Pages: 17

SKR E3 DIP V1.0

Brand: BIGTREETECH Pages: 10

B560M DS3H PLUS

Brand: Gigabyte Pages: 42

Brand: ST Pages: 82

Brand: Silicon Laboratories Pages: 16

790XT-G35 series

Brand: MSI Pages: 103

Brand: Advantech Pages: 116

Brand: H-Tec Pages: 28

Brand: Magic-Pro Computer Pages: 40

Brand: QDI Pages: 47

Brand: Acorp Pages: 74

Brand: Zeal-All Pages: 9

Brand: Fujitsu Pages: 30

LANPARTY UT 915P-T12

Brand: DFI Pages: 124

Brand: DG Pages: 18

Brand: Mitsubishi Electric Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands