Yamaha F30 Page 32 Owner'S Manual Download

Page: 32 / 120

Components

WARNING

EWM00021

The fuel tank supplied with this engine is
its dedicated fuel reservoir and must not
be used as a fuel storage container. Com-
mercial users should conform to relevant
licensing or approval authority regula-
tions.

Fuel joint

This joint is used to connect the fuel line.

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

If using the type “B” portable fuel tank, the
parts of the fuel tank are as follows.
This fuel tank conforms to Evaporative Emis-

sions Regulations for marine fuel systems
enacted by the US Environmental Protection
Agency (EPA).

WARNING

EWM00021

Fuel joint

This joint is used to connect the fuel line.

Fuel gauge

This gauge shows the approximate amount
of fuel remaining in the fuel tank.

Pressure relief tab

This tab is attached to the filler hole of the
fuel tank.

Fuel tank cap

This cap seals the fuel tank. To loosen the

1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw

ZMU07594

1. Fuel joint
2. Fuel gauge
3. Pressure relief tab
4. Fuel tank cap
5. Air vent screw

ZMU07573

6BG-9-3F-E0.book 26 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands