Yamaha F30 Page 63 Owner'S Manual Download

Page: 63 / 120

Operation

TIP:



When using the fuel tank on the boat, a
fuel valve may also be equipped on the
boat. Open the fuel valve.



Check the boat’s manual for the position of
the fuel valve.

When using the portable fuel tank “B”, send
fuel to the outboard motor according to the
following procedure.

1. To loosen the air vent screw, turn it

counterclockwise until it stops.

2. Check the direction of the fuel hose.

Make sure that the arrow of the primer
pump points toward the outboard motor.

3. Align the fuel joint on the fuel hose with

the fuel joint on the outboard motor and
firmly connect the fuel hose to the joint
while pinching the joint.

1. Arrow
2. Primer pump

ZMU07580

1. Air vent screw

1. Toward the outboard motor
2. Arrow
3. Primer pump
4. Toward the fuel tank

ZMU07445

ZMU07452

6BG-9-3F-E0.book 57 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands