Yamaha F30 Page 33 Owner'S Manual Download | Manualshive

Page: 33 / 120

background image

Components

27

cap, press and hold the pressure relief tab
and turn the cap counterclockwise.

Air vent screw

This screw is on the fuel tank cap. When
turning the air vent screw counterclockwise,
it is loosened and the pressure in the fuel
tank is released to a certain pressure. Air is
allowed to enter the fuel tank while operating
the engine.

EMU46751

Yamaha Security System (Y-COP)

NOTICE

ECM02461

The Yamaha Security System is sold in
conformity with the relevant laws and
regulations regarding radio wave trans-
mission. Therefore, if this product is used
outside the country where it was sold, it
may violate the laws or regulations re-
garding radio wave transmission in the
country it is used in. For details, consult
your Yamaha dealer.

The Yamaha Security System, which pro-
tects against theft, consists of the receiver
and remote control transmitters. The
Yamaha Security System is available from
your Yamaha dealer. For details, consult
your Yamaha dealer.

The engine cannot be started if the security
system is in the lock mode. The engine can
be started only in the unlock mode. For more
information, see the installation and owner’s
manual included with the security system.

TIP:

The security system cannot be used with
quad engine applications or Helm Master®.

EMU26182

Remote control box

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

EMU26191

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35



(a detent can be felt).

Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

1. Remote control transmitter
2. Receiver

2

1

ZMU08527

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch
6. Engine shut-off switch
7. Throttle friction adjuster

1
2

3

5

4

6

7

ZMU01723

6BG-9-3F-E0.book 27 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
31
32
33
34
35
...
»

Summary of Contents for F30

























































































































Reviews:

No comments

Related manuals for F30

Brand: Texas Instruments Pages: 47

Brand: ablelogic Pages: 47

MITX-DNV0 Series

Brand: Quanmax Pages: 84

Brand: P&E Microcomputer Systems Pages: 53

MT9J003I12STCVH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: ASROCK Pages: 114

Brand: Texas Instruments Pages: 8

Brand: Sundance Spas Pages: 21

Brand: Biostar Pages: 118

Brand: QDI Pages: 58

Brand: trimond Pages: 43

Brand: OLIMEX Pages: 26

Brand: Intel Pages: 1

Brand: C&T Solution Pages: 90

Brand: TYAN Pages: 130

GA-HA65M-D2H-B3

Brand: Gigabyte Pages: 104

Brand: JETWAY Pages: 58

Brand: MSI Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands