Yamaha F30 Page 48 Owner'S Manual Download

Page: 48 / 120

Instruments and indicators

Lock mode

Make sure that the Yamaha Security System
indicator is off before starting the engine.

Water separator-alert indicator

If water has accumulated in the water sepa-
rator (fuel filter) while cruising, the water sep-
arator-alert indicator will start to blink.

Stop the engine immediately and see page
100 of this manual to drain the water from the
fuel filter. Get back to the port soon and con-
sult a Yamaha dealer immediately.

NOTICE

ECM00911

Gasoline mixed with water could cause
damage to the engine.

Engine trouble-alert indicator

If the engine malfunctions while cruising, the

engine trouble-alert indicator will start to
blink. Get back to the port soon and consult
a Yamaha dealer immediately.

NOTICE

ECM00921

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer im-
mediately.

Low battery voltage alert

If the battery voltage drops, the battery volt-
age value will start to blink.

Get back to the port soon if the low battery
voltage alert device has activated. For charg-
ing the battery, consult your Yamaha dealer.

Overheat-alert indicator

If the engine temperature rises too high while
cruising, the overheat-alert indicator will start

1. Yamaha Security System indicator (optional)

1. Water separator-alert indicator

SET

MODE

ZMU08412

ZMU08413

1. Engine trouble-alert indicator

1. Battery voltage value

ZMU08414

ZMU08415

6BG-9-3F-E0.book 42 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands