Yamaha F30 Page 110 Owner'S Manual Download

Page: 110 / 120

Trouble Recovery

104

trical components when starting or op-
erating the motor. You could get an
electrical shock.

EMU44403

Emergency starting engine

1. Remove the top cowling.
2. Remove the flywheel cover after remov-

ing the bolt.

3. Prepare the engine for starting. For fur-

ther information, see page 58. Be sure
the engine is in neutral and that the clip
is attached to the engine shut-off switch.

4. Turn on the main switch.

5. Insert the knotted end of the emergency

starter rope into the notch in the flywheel
rotor and wind the rope around the fly-
wheel several turns clockwise.

6. Give a strong pull straight out to crank

the engine. Repeat if necessary.

WARNING! Do not install the top
cowling when engine is running.

[EWM00622]

ZMU06429

ZMU02334

TART

OFF

ZMU01906

ZMU06430

6BG-9-3F-E0.book 104 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands