Yamaha F30 Page 59 Owner'S Manual Download

Page: 59 / 120

Operation

1. Disconnect the fuel hose from the fuel

tank and tighten the air vent screw on
the fuel tank cap.

2. Remove the portable tank from the boat.
3. Fill the fuel tank with fuel, but do not

overfill.

WARNING! Do not overfill.

Otherwise fuel can expand and over-
flow if the temperature increases.

[EWM02611]

TIP:



Wipe up any spilled gasoline immediately
with dry rags.



Dispose of rags properly according to local
laws or regulations.

4. Tighten the filler cap securely.
When using the portable fuel tank “B”, fill the
fuel tank according to the following proce-
dure.

1. Disconnect the fuel hose from the fuel

joint on the fuel tank.

1. Fuel joint
2. Fuel hose

1. Air vent screw

Fuel tank capacity:

24 L (6.34 US gal, 5.28 Imp.gal)

ZMU07581

ZMU07597

ZMU02834

ZMU07580

6BG-9-3F-E0.book 53 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Summary of Contents for F30

























































































































Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands

Yamaha F30, Owner'S Manual

Search results

Summary of Contents for F30

Reviews:

Related manuals for F30

Brands by name

Popular brands