Yamaha Electone F-25 Owner'S Manual Download Page 80

Page: 80 / 122

Operation

2. Place the tilt lock lever in the release/up

position.

3. Slightly tilt the outboard motor up. The

tilt support bar will lock automatically,
supporting the outboard motor in a par-
tially raised position. This outboard mo-
tor has 2 positions for shallow water
cruising.

4. To return the outboard motor to the nor-

mal running position, place the remote
control lever / gear shift lever in neutral.

5. Place the tilt lock lever in the lock/down

position, then slightly tilt the outboard
motor up until the tilt support bar auto-
matically returns to the free position.

6. Slowly lower the outboard motor to the

normal position.

EMU28082

Hydro tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00272



Run the boat at the lowest possible
speed when using the shallow water
cruising system.



Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of

ZMU03087

ZMU06521

ZMU06539

ZMU04851

ZMU02306

6BP-9-3B-1E0.book 74 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Summary of Contents for Electone F-25



























































































































Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands

Yamaha Electone F-25, Owner'S Manual

Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands