Yamaha Electone F-25 Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 122

background image

Specifications and requirements

23

peller pitch may be necessary.

Sacrificial anodes are attached to the out-
board motor to provide corrosion protection
and must never be painted.
Sacrificial anodes made from a different ma-
terial may be necessary for maximum corro-
sion protection due to your local water
conditions. Please consult your Yamaha
dealer.

NOTICE

ECM02421

Painted sacrificial anodes will not provide
corrosion protection.

EMU36342

Motor disposal requirements

Never illegally discard (dump) the motor.
Yamaha recommends consulting the dealer
about discarding the motor.

EMU36353

Emergency equipment

Keep the following items onboard in case
there is trouble with the outboard motor.



A tool kit with assorted screwdrivers, pli-
ers, wrenches (including metric sizes), and
electrical tape.



Waterproof flashlight with extra batteries.



An extra engine shut-off cord (lanyard)
with clip.



Spare parts, such as an extra set of spark
plugs.

Consult your Yamaha dealer for details.

EMU25223

Emission control information

EMU25232

This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.

EMU25245

Approval label of emission control certif-
icate

This label is attached at the location shown.
New Technology; (4-stroke/HPDI) EM

1. Approval label location

1. Approval label location

1

ZMU08208

1

ZMU08303

6BP-9-3B-1E0.book 23 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
27
28
29
30
31
...
»

Summary of Contents for Electone F-25



























































































































Reviews:

No comments

Related manuals for Electone F-25

Brand: Olympus Pages: 362

Brand: Olympus Pages: 8

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

Brand: Cecomp Pages: 4

Brand: Emos Pages: 76

Brand: Laney Pages: 4

Brand: Hanna Instruments Pages: 52

Recordall Series

Brand: Badger Meter Pages: 8

Brand: GTR Pages: 8

Brand: Sagola Pages: 16

Brand: KEM Pages: 49

Brand: Agilent Technologies Pages: 20

Brand: RADWAG Pages: 12

Brand: Maxtec Pages: 13

Brand: NARDA Pages: 60

Brand: Dwyer Instruments Pages: 2

Brand: Diamond Amplification Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands