Yamaha Electone F-25 Owner'S Manual Download Page 69 | Manualshive

Page: 69 / 122

background image

Operation

63

2. After the engine is at idle speed in gear

move the remote control lever / gear
shift lever firmly and crisply into the neu-
tral position.

EMU31743

Stopping boat

WARNING

EWM01511



Do not use the reverse function to slow
down or stop the boat as it could cause
you to lose control, be ejected, or im-
pact the steering wheel or other parts of
the boat. This could increase the risk of
serious injury. It could also damage the
shift mechanism.



Do not shift into reverse while traveling
at planing speeds. Loss of control, boat
swamping, or damage to the boat could
occur.

The boat is not equipped with a separate
braking system. Water resistance stops it af-
ter the throttle lever is moved back to idle.
The stopping distance varies depending on
gross weight, water surface conditions, and
wind direction.

ZMU06652

N

ZMU01771

N

ZMU06521

6BP-9-3B-1E0.book 63 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
67
68
69
70
71
...
»

Summary of Contents for Electone F-25



























































































































Reviews:

No comments

Related manuals for Electone F-25

Brand: Bante Instruments Pages: 6

Brand: Hammond Organ Pages: 25

Brand: Hammond Organ Pages: 87

Brand: IFM Pages: 2

Brand: Larson Davis Pages: 536

Brand: MADDALENA Pages: 4

Brand: Macnaught Pages: 4

Brand: UEi Pages: 8

ProcessMaster FEP630 series

Brand: ABB Pages: 92

Brand: National Instruments Pages: 15

Brand: AEMC Pages: 4

Brand: Clavitech Pages: 56

Brand: Anritsu Pages: 29

Brand: VWR Pages: 44

Brand: PCB Piezotronics Pages: 11

Amplitude T Series

Brand: OTOVATION Pages: 15

PowerMaster MTA15Z

Brand: PowerMetrix Pages: 13

Brand: Cewe Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands