Yamaha Electone F-25 Owner'S Manual Download Page 37

Page: 37 / 122

Components

EMU25925

Gear shift lever

Move the gear shift lever forward to engage
the forward gear or rearward to engage the
reverse gear.

EMU25943

Throttle grip

The throttle grip is on the tiller handle. Turn
the grip counterclockwise to increase speed
and clockwise to decrease speed.

EMU25963

Throttle indicator

The fuel consumption curve on the throttle
indicator shows the relative amount of fuel
consumed for each throttle position. Choose
the setting that offers the best performance
and fuel economy for the desired operation.

1. Forward “ ”
2. Neutral “ ”
3. Reverse “ ”

1. Forward “ ”

ZMU06486

2. Neutral “ ”
3. Reverse “ ”

ZMU03034

6BP-9-3B-1E0.book 31 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Summary of Contents for Electone F-25



























































































































Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands

Yamaha Electone F-25, Owner'S Manual

Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands