Yamaha Electone F-25 Owner'S Manual Download Page 81

Page: 81 / 122

Operation

the water, increasing the chance of ac-
cident and personal injury.

NOTICE

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU32841

Procedure for hydro tilt models

1. Place the gear shift lever in neutral.

2. Pull the tilt lock lever up to the release

position.

3. Slightly tilt the outboard motor up to the

desired position and push the tilt lock le-
ver down to the lock position.

4. To return the outboard motor to the nor-

mal running position, pull the tilt lock le-

ver up to the release position and slowly
tilt the outboard motor down.

5. Push the tilt lock lever down to the lock

position.

EMU32852

Power trim and tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM00261

EMU32914

Procedure for power trim and tilt models

1. Place the remote control lever / gear

shift lever in neutral.

ZMU06521

ZMU07537

ZMU07536

ZMU01771

6BP-9-3B-1E0.book 75 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Summary of Contents for Electone F-25



























































































































Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands

Yamaha Electone F-25, Owner'S Manual

Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands