Yamaha Electone F-25 Owner'S Manual Download Page 58

Page: 58 / 122

Operation

5. While pressing and holding the pressure

relief tab under the fuel tank cap, slowly
turn the fuel tank cap counterclockwise
1/4 turn.

TIP:

Release the fuel vapor contained in the fuel
tank.
6. While pressing and holding the pressure

relief tab under the fuel tank cap again,
turn the fuel tank cap counterclockwise
to remove it.

7. Fill the fuel tank with fuel.

WARNING!

Do not overfill. Otherwise fuel can ex-
pand and overflow if the temperature
increases.

[EWM02611]

TIP:



Wipe up any spilled gasoline immediately
with dry rags.



Dispose of rags properly according to local
laws or regulations.

8. Turn the fuel tank cap clockwise to tight-

en until a click is heard.

9. Turn the air vent screw clockwise to

close it.

1. Pressure relief tab
2. Fuel tank cap

ZMU07446

ZMU07447

Fuel tank capacity:

25 L (6.60 US gal, 5.50 Imp.gal)

1. Fuel tank cap

ZMU07448

ZMU07449

6BP-9-3B-1E0.book 52 ページ２０１５年１１月１６日　月曜日　午後５時５７分

Summary of Contents for Electone F-25



























































































































Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands

Yamaha Electone F-25, Owner'S Manual

Search results

Summary of Contents for Electone F-25

Reviews:

Related manuals for Electone F-25

Brands by name

Popular brands