Yamaha Electone F-25 Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 122

background image

Specifications and requirements

20

EMU25771

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is in neutral. Always select neutral
before starting the engine.

EMU41953

Engine oil requirements

Select an oil grade according to the average
temperatures in the area where the outboard
motor will be used.

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an
alternative oil grade listed under Recom-
mended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36361

Fuel requirements

EMU41333

Gasoline

Use a good quality gasoline that meets the
minimum octane requirement. If knocking or
pinging occurs, use a different brand of gas-
oline or premium unleaded fuel. Yamaha
recommends that you use alcohol-free gaso-
line (see Gasoline with Ethanol) whenever
possible.
The use of a poor quality gasoline may result
in starting and running problems. If you en-
counter drivability problems, which you sus-
pect could be related to the fuel you are
using, Yamaha recommends that you switch
to a recognized high quality brand of gaso-
line, such as a gasoline that is advertised as
Top Tier Detergent Gasoline.

NOTICE:

Fail-

ure to comply with these recommenda-

2. Propeller pitch in inches
3. Type of propeller (propeller mark)

Recommended engine oil:

YAMALUBE 4M FC-W or 4-stroke out-

board motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30

API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50

API SH/SJ/SL

Engine oil quantity (without oil filter

replacement):

1.4 L (1.48 US qt, 1.23 Imp.qt)

Engine oil quantity (with oil filter re-

placement):

1.6 L (1.69 US qt, 1.41 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

6BP-9-3B-1E0.book 20 ページ２０１５年１１月１６日　月曜日　午後５時５７分

«
...
24
25
26
27
28
...
»

Summary of Contents for Electone F-25



























































































































Reviews:

No comments

Related manuals for Electone F-25

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: D-tect Systems Pages: 19

Brand: IET Labs Pages: 114

Ultraprobe 9000

Brand: UE Systems Pages: 25

ULTRAPROBE 10000

Brand: UE Systems Pages: 6

Brand: WAGO Pages: 96

Brand: Fender Pages: 20

Smart Probes 115i

Brand: TESTO Pages: 17

Brand: bentrup Pages: 9

Brand: Mic Pages: 2

Brand: Technoline Pages: 1

Brand: Kawai Pages: 36

Brand: Kawai Pages: 72

Brand: Kingfisher Pages: 52

Brand: Amrutha Technologies Pages: 22

Brand: Straightpoint Pages: 24

Brand: Xsens Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands