XTA MX Series Operator'S Manual Download Page 33

MX Series — MX24 Operating Instructions 

 

 

 

 

        Page 33 

ta

x

 

Performance Of Your MX24:  Specifications 
 

Audio Specifications  
 

Parameter (Units) 

MX24

Analogue line inputs (incl. stereo line input) 

 

Channels

(2 x 4) + (1 x 2) 

Input impedance (Ohms) 

10k 

Max input level (dBu)

+22 

CMR @ 1kHz (dB)

>

50 

THD 20-20k (%)

<

0.002 

Dynamic range typ. (dB)

116

Analogue microphone input 

 

Channels

Input impedance (Ohms) 

10k 

Max input level (dBu)

+22 

Equivalent Input Noise @ 150R Impedance (dBu)

-127 

CMR @ 1kHz (dB)

>

50 

Analogue outputs 

 

Output source impedance (Ohms)

70 

Min load impedance (Ohms)

300 

Max output level (dBu)

+22 

Dynamic range typ. (dB)

118.5 

Headphone output (stereo jack — mono signal) 

 

Min load impedance/Ch. (Ohms)

THD 20-20k (%)

<

0.013 

Max output power (W)

~1.5

Frequency Response, +0/0.2dB (Hz)

20 — 20k

AES digital outputs (MX24-A) 

 

Channels @ 96kHz (or External clock fs)

2 x 2 

Voltage @ 110R termination balanced (V)

2.5 

AES digital inputs (MX24-A) 

 

Channels

2 x (2 x 2) 

Sample rate (kHz)

44.1 — 192 

Sample Rate Converters

4 x 2Ch. 

External word clock input

2

 

 

Impedance termination (Ohms)

150 

Accepted voltage range (V)

0.2 — 7.0 

Dante network Audio I-O (MX24-D) 

 

Input channels available

Output channels available

Sample rates supported (kHz)

48/96 

 
 
System Specifications 
 

Parameter (Units) 

MX24

Mains supply (V AC) 

100-240 

Power Consumption (W) 

<

50W 

Dimensions H x W x D (mm) 

 

Unit (excl. connectors)

88 x 482 x 335 

Boxed

230 x 580 x 560 

Boxed Shipping — all except UK

250 x 610 x 600 

Weight (kgs) 

 

Unit

5.1 

Boxed

6.3 

 
 
 
Due to continuing product improvement, the above specifications are subject to change. 

 

2

 External word clock input is used to synchronise AES outputs only (MX24-A) 

Summary of Contents for MX Series










































Reviews: