Xerox 4150 - WorkCentre B/W Laser, Service Manual

Page: 103 / 631

January 2016
2-30 WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
05-200
Status Indicator RAPs
05-200 DADF Jam 2 RAP
05-200 The lead edge or trail edge of the document failed to actuate or deactuate the gate sen-
sor within the correct time.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
4150 Checkout
Refer to Wiring Diagram 11 . Perform the following:
1. Raise the DADF. Check the CVT ramp, part of the CVT glass assembly, PL 14.10 Item 22 .
If necessary, install a new CVT glass assembly, PL 14.10 Item 22 .
2. Open the DADF top cover assembly, PL 5.15 Item 11 . Remove all jammed paper.
3. Raise the DADF input tray, PL 5.10 Item 5 . Remove all jammed paper.
4. Check that the exit assembly, PL 5.20 Item 26 is closed.
5. Check the document path for damage or obstructions.
6. Check that the following components are clean and rotate freely.
• Gate roll, PL 5.25 Item 15 .
• Gate roll idlers, PL 5.10 Item 18 .
• Exit roll, PL 5.20 Item 2 .
• Exit roll idlers, PL 5.20 Item 20 .
7. Check that the gate sensor actuator, PL 5.10 Item 26 moves freely and is not damaged.
8. Enter dC330 code 05-150. Check the gate sensor (Q05-150), PL 5.10 Item 24 . if neces-
sary, install a new gate sensor, PL 5.10 Item 24 .
9. Remove the DADF rear cover, PL 5.10 Item 4 . Enter dC330 code 05-200. Check that the
DADF scan motor runs, PL 5.25 Item 12 and drives the gate roll, PL 5.25 Item 15 .
10. Enter code 05-210. Check that the DADF duplex motor, PL 5.25 Item 5 runs and drives
the exit roll, PL 5.20 Item 2 .
11. Check the wiring between the DADF scan motor and CN4 on the DADF PWB .
12. Check the wiring between the duplex motor and CN5 on the DADF PWB .
13. If necessary, install new components:
• DADF PWB, PL 5.20 Item 6 .
• DADF scan motor, PL 5.25 Item 12 .
• DADF scan motor assembly, PL 5.25 Item 10 .
• Duplex motor assembly, PL 5.25 Item 4 .
• Document transport assembly, PL 5.10 Item 2 .
4250/4260 Checkout
Refer to Wiring Diagram 29 . Perform the following:
1. Raise the DADF. Check the CVT ramp, part of the CVT glass assembly, PL 14.13 Item 32 .
If necessary, install a new CVT glass assembly, PL 14.13 Item 32 .
2. Open the DADF top cover assembly, PL 5.30 Item 2 . Remove all jammed paper.
3. Raise the DADF input tray, PL 5.30 Item 11 . Remove all jammed paper.
4. Check the document path for damage or obstructions.
5. Check that the following components are clean and rotate freely.
• Gate roll, PL 5.50 Item 18 .
• Gate roll idlers, PL 5.35 Item 8 .
• Upper exit roll, PL 5.45 Item 20 .
• Upper exit roll idlers, PL 5.55 Item 9 .
6. Check that the gate sensor actuator, PL 5.55 Item 3 moves freely and is not damaged.
7. Enter dC330 code 05-150. Check the gate sensor (Q05-150), PL 5.55 Item 1 . If neces-
sary, install a new gate sensor, PL 5.55 Item 1 .
8. Remove the DADF rear cover, PL 5.30 Item 13 and lower guide, PL 5.50 Item 1 . Enter
dC330 code 05-200. Check that the DADF scan motor runs, PL 5.30 Item 6 and drives
the gate roll, PL 5.50 Item 18 .
9. Enter code 05-210. Check that the DADF duplex motor, PL 5.30 Item 7 runs and drives
the upper exit roll, PL 5.45 Item 20 .
10. Check the wiring between the DADF scan motor and CN4 on the DADF PWB .
11. Check the wiring between the duplex motor and CN5 on the DADF PWB .
12. If necessary, install new components:
• DADF PWB, PL 5.30 Item 24 .
• DADF scan motor assembly, PL 5.30 Item 6 .
• Duplex motor assembly, PL 5.30 Item 7 .
• Document transport assembly, PL 5.30 Item 26 .