Note
After a waiting time of approx. 10
seconds the start-up procedure can
be repeated up to 5 times. Then the
vehicle must be checked and the bat-
tery of the device must be charged.
Engine is running
■
Switch off the device after approx. 2 minu
-
tes.
■
Remove booster cable clamps.
Switching on 12 V or 24 V voltage
manually
■
Check LED
[8]
.
■
Press the MAN button
[3]
.
Important
Booster cable clamps are
live!
Jump start
■
Start engine of the vehicle.
Caution
Do not disconnect or switch off the
de-
vice directly after start-up as other-
wise the on-board electronics and/
■
Switch off the device after approx. 2 minutes.
■
Remove booster cable clamps.
Caution
If the engine is not running after
6 seconds, the start-up procedure
must be interrupted immediately as
otherwise the battery booster kit and
the vehicle may be damaged.
Note
After a waiting time of approx. 10
sec-onds the start-up procedure can
be repeated up to 5 times. Then the
vehicle must be checked and the bat-
tery of the device must be charged.
Note
The electronic control switches off
the voltage after approx. 45 minutes
in order to avoid unintentional
discharge of the device batteries.
Jumpstart without vehicle battery
Caution
Reverse connection protection
not active with this application
(inverse voltage missing)!
■
Connect the booster cable clamps directly to the
vehicle‘s battery terminals.
■
Swith on (press ON button
[1]
.
■
Select the voltage (12V
[5]
or 24V
[6]
).
■
Press the MAN button
[3]
(You shoud hear an
audible „click“; the contactors are switched on
and the terminals of the battery booster kit are
live).
■
Start the engine (please pay attention to the
warnings with regard to the maximum allowed
start-up time - see instructions).
■
After starting up the engine successfully, swich
the battery booster kit off (press the OFF
button
[12]
).
■
Disconnect the terminals in reverse order (at first
disconnect the black terminal (-) than the red
terminal (+)).
■
Connect the battery booster kit to the supplied
charger and charge it.
or the generator may be damaged!
Caution
Do not disconnect or switch off the
device! Otherwise the on-board
elec-tronics and/or the generator
may be damaged!
Engine is running
■
Switch off the device
■
Remove booster cable clamps.
Charging
■
Charge the device for 24 hours before using it
for the first time.
■
Connect the device to the charger provided
after each start-up.
3
This will ensure that the device remains ready
for use.
Note
It is not a problem to have the
device connected to the charger
provided permanently.
11
11
Note
After a waiting time of approx. 10 sec
-
onds the start-up procedure can be re-
peated up to 5 times. Then the vehicle
must be checked and the battery of the
device must be charged.
Engine is running
■
Switch off the device after approx. 2 minutes.
■
Remove booster cable clamps.
Switching on 12 V or 24 V voltage
manually
■
Check LED
[8]
.
■
Press the MAN button
[3]
.
Important
Booster cable clamps are live!
Jump start
■
Start engine of the vehicle.
Caution
Do not disconnect or switch off the de-
vice directly after start-up as otherwise
the on-board electronics and/or the
generator may be damaged!
■
Switch off the device after approx. 2 minutes.
■
Remove booster cable clamps.
Caution
If the engine is not running after 6 sec
-
onds, the start-up procedure must be
interrupted immediately as otherwise
the battery booster kit and the vehicle
may be damaged.
Note
After a waiting time of approx. 10 sec
-
onds the start-up procedure can be re-
peated up to 5 times. Then the vehicle
must be checked and the battery of the
device must be charged.
Note
The electronic control switches off the
voltage after approx. 45 minutes in
order to avoid unintentional discharge
of the device batteries.
Jumpstart without vehicle battery
Caution
Reverse connection protection not
active with this application (inverse
voltage missing)!
■
Connect the booster cable clamps directly to the
vehicle's battery terminals.
■
Swith on (press ON button
[1]
.
■
Select the voltage (12V
[5]
or 24V
[6]
).
■
Press the MAN button
[3]
(You shoud hear an
audible "click"; the contactors are switched on
and the terminals of the battery booster kit are
live).
■
Start the engine (please pay attention to the
warnings with regard to the maximum allowed
start-up time - see instructions).
■
After starting up the engine successfully, swich
the battery booster kit off (press the OFF
button
[12]
).
■
Disconnect the terminals in reverse order (at first
disconnect the black terminal (-) than the red
terminal (+)).
■
Connect the battery booster kit to the supplied
charger and charge it.
Caution
Do not disconnect or switch off the
device! Otherwise the on-board elec-
tronics and/or the generator may be
damaged!
Engine is running
■
Switch off the device
■
Remove booster cable clamps.
Charging
■
Charge the device for 24 hours before using it
for the first time.
■
Connect the device to the charger provided
after each start-up.
3
This will ensure that the device remains ready
for use.
Note
It is not a problem to have the device
connected to the charger provided
permanently.
