Work Pro LightMouse LM-5 User Manual Download Page 55

Page: 55 / 64

Creating a Push Button to play a selected show manually

The entered command can run a pre-selected show the MultiToggle previously seen. This mode

plays scenes that make the show manually, we can move forward and backward between them

at any time regardless of the Stand Time.

As a push button can only have 2 values oscillating between 0 and 1, in Value Range section

we assign to the minimum (standby) and the maximum value (Active) the value 0 and 1

respectively.

To function properly activate the Local Feedback Off, of this So the Push Button not light up

when you click on the iPad, otherwise when the LM-5 play the show.

The specific command used is:

/dmx/play/show/play_stpgo ,f: It plays the selected show in Stop & Go mode.

Parameters:

Float: 1 or 0. If value=0, it does not effect

Note:

It returns [3]

LM-5 Reply packages for certain actions

53 User Manual

Summary of Contents for LightMouse LM-5

































































Search results

Summary of Contents for LightMouse LM-5

Reviews:

Related manuals for LightMouse LM-5

Brands by name

Popular brands

Work Pro LightMouse LM-5, User Manual

Search results

Summary of Contents for LightMouse LM-5

Reviews:

Related manuals for LightMouse LM-5

Brands by name

Popular brands