Work Pro LightMouse LM-5 User Manual Download Page 8

Page: 8 / 64

SETUP AND USE

WorkNet Mode

Art-Net Mode

In WorkNet mode, the LM-5 operates as a receiver of information sent DMX by the device

LM-3E (issuer). Therefore, in this operation mode, the LM-5 always be used in combination

with a LM-3E, and both devices mustconfigured in the same group (or DMX Universe). In this

way, and generalized to more of a receiving device, the information sent by a LM-3E will be

received by LM-5 those configured in the same group as the LM-3E issuer.

Note: Only LM-3E device can be associated with one or more devices LM-5.

WorkNet is a proprietary protocol that runs on any standard network TCP / IP. The protocol is

unicast, in order not to decrease the efficiency of network.

Both the LM-3E as the LM-5 is configured automatically, and need no network configuration. The

IP address and Subnet Mask is obtained automatically, so that both devices are in the same

subnet and and can communicate with each.

In Art-Net mode, LM-5 operates as an Art-Net node itself, receiving all information sent by an

Art-Net emitter. In this case the concept group is replaced by universe, further including the

concept of Subnet, such as specified in Art-Net protocol.

The LM-5 is a plug and play device and requires no network configuration, this is set automatically

obtaining an IP address 2.x.x.x and a subnet mask of 255.0.0.0 as specified by Art-Net protocol.

This mode is enabled and configured using the switches on the rear panel, This point will be

explained later on.

6 User Manual

Summary of Contents for LightMouse LM-5

































































Search results

Summary of Contents for LightMouse LM-5

Reviews:

Related manuals for LightMouse LM-5

Brands by name

Popular brands

Work Pro LightMouse LM-5, User Manual

Search results

Summary of Contents for LightMouse LM-5

Reviews:

Related manuals for LightMouse LM-5

Brands by name

Popular brands