Wood-mizer Sawmill LT20 AC MH Series Safety, Setup, Operation & Maintenance Manual Download

Page: 6 / 106

Table of Contents

Section-Page

25doc092506

Table of Contents

SECTION 3 MAINTENANCE

3-1

3.1

Wear Life................................................................................................................... 3-1

3.2

Blade Guides ............................................................................................................. 3-2

3.3

Sawdust Removal ...................................................................................................... 3-2

3.4

Carriage Track, Wiper & Scrapers ............................................................................ 3-3

3.5

Vertical Mast Rails .................................................................................................... 3-4

3.6

Miscellaneous ............................................................................................................ 3-5

3.7

Blade Tensioner......................................................................................................... 3-6

3.8

Blade Wheel Belts ..................................................................................................... 3-6

3.9

Drive Belt Adjustment .............................................................................................. 3-7

3.10

Up/Down System....................................................................................................... 3-9

3.11

Power Feed System ................................................................................................. 3-11

SECTION 4

TROUBLESHOOTING GUIDE

4-1

4.1

Sawing Problems ....................................................................................................... 4-1

4.2

Electrical Problems.................................................................................................... 4-3

4.3

Power Feed Problems ................................................................................................ 4-5

4.4

Hydraulic Problems ................................................................................................... 4-7

4.5

Engine/Motor and Drive Pulleys Alignment........................................................... 4-11

SECTION 5 SAWMILL ALIGNMENT

5-1

5.1

Pre-Alignment Procedures......................................................................................... 5-1

5.2

Frame Setup............................................................................................................... 5-2

5.3

Blade Installation And Alignment............................................................................. 5-2

5.4

Blade Wheel Alignment ............................................................................................ 5-6

5.5

Adjusting The Lower Track Rollers........................................................................ 5-11

5.6

Adjusting Bed Rails To The Blade.......................................................................... 5-14

5.7

Blade Guide Arm Vertical Adjustment ................................................................... 5-16

5.8

Carriage Backlash Removal .................................................................................... 5-18

5.9

Blade Guide Rope Adjustment................................................................................ 5-20

5.10

Blade Guide Arm Horizontal Adjustment............................................................... 5-21

5.11

Aligning the Blade Guides ...................................................................................... 5-23

5.12

Blade Deflection...................................................................................................... 5-24

5.13

Blade Guide Vertical Tilt Adjustment..................................................................... 5-25

5.14

Blade Guide Spacing ............................................................................................... 5-27

5.15

Horizontal Tilt Adjustment...................................................................................... 5-28

5.16

Horizontal Adjustment of Side Supports ............................................................ 5-29

5.17

Vertical Adjustment of Side Supports................................................................. 5-30

5.18

Saw Head Tilt .......................................................................................................... 5-31

5.19

Blade Height Scale Adjustment............................................................................... 5-33

Summary of Contents for Sawmill LT20 AC MH Series











































































































Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands

Wood-mizer Sawmill LT20 AC MH Series, Safety, Setup, Operation & Maintenance Manual

Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands