Wood-mizer Sawmill LT20 AC MH Series Page 103 Safety, Setup, Operation & Maintenance Manual Download

Page: 103 / 106

SAWMILL ALIGNMENT

Vertical Adjustment of Side Supports

SAWMILL ALIGNMENT

doc092506

5-30

5.17

Vertical Adjustment of Side Supports

Place a flat board across the bed rails.

Swing a side support up so that it is vertical.

Pull back at the top of the support to eliminate slack as if a log were being clamped
against it.

See Figure 5-28.

Check the angle of each support with a square on the board.

The side support should be 90

to the bed rails or leaning forward 1.0 mm (0

04"). Loosen

the top adjustment bolt, adjust the side support, and retighten the bolt.

Repeat for the remaining side supports.

FIG. 5-28

Summary of Contents for Sawmill LT20 AC MH Series











































































































Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands

Wood-mizer Sawmill LT20 AC MH Series, Safety, Setup, Operation & Maintenance Manual

Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands