Wood-mizer Sawmill LT20 AC MH Series Safety, Setup, Operation & Maintenance Manual Download

Page: 67 / 106

Troubleshooting Guide

Power Feed Problems

Troubleshooting Guide

doc092506

4-5

4.3

Power Feed Problems

PROBLEM

CAUSE

SOLUTION

Power Feed Is Jerky At Low
Speeds Or Does Not Move
Until Speed Is Above Halfway
Mark.

Drum switch is dirty.

Clean drum switch and lubricate
with contact grease supplied by
Wood-Mizer.

Drum switch contacts are bad

Check that contacts are in good
condition and positively close cir-
cuit.

Speed switch is worn.

Replace the speed switch.

Speed switch is blocked.

Turn off the power for 20 sec-
onds and turn it back on.

Power Feed Is Jerky, But
Power Feed Motor Runs Prop-
erly At All Speeds.

Problem is mechanical.

Refer to the Mechanical Test.

Summary of Contents for Sawmill LT20 AC MH Series











































































































Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands

Wood-mizer Sawmill LT20 AC MH Series, Safety, Setup, Operation & Maintenance Manual

Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands