Wood-mizer Sawmill LT20 AC MH Series Safety, Setup, Operation & Maintenance Manual Download

Page: 72 / 106

Troubleshooting Guide

Hydraulic Problems

4-10

doc092506

Troubleshooting Guide

PROBLEM

CAUSE

SOLUTION

Hydraulic Side Supports Go
Down Before Or At Same
Time As Log Turner

Dirt in sequence valve

Remove sequence valves and
clean thoroughly with kero-
sene.

NOTE:

Be sure to reas-

semble the valve and install it
in its original position on the
cylinder

Retainer in sequence valve
worn

Replace sequence valve

Low air temperature causing
fluid to thicken

Allow fluid to warm up. Syn-
thetic fluids are available that
allow for hydraulic operation
in cold weather conditions
(Mobil SHC 526)

Hydraulic Turner Goes Up
Before Or At Same Time As
Side Supports

Spring weakening in
sequence valve

Locate sequence valve at top
of turner cylinder. Turn heavy
spring in about 1/4 turn

Dirt in sequence valve

Remove sequence valves and
clean thoroughly with kero-
sene.

NOTE:

Be sure to reas-

semble the valve and install it
in its original position on the
cylinder

Retainer in sequence valve
worn

Replace sequence valve

Low air temperature causing
fluid to thicken

Allow fluid to warm up. Syn-
thetic fluids are available that
allow for hydraulic operation
in cold weather conditions.
(Mobil SHC 526)

Springs weakening in
sequence valve.

Locate sequence valve at bot-
tom of turner cylinder. Turn
heavy spring in about 1/4 turn

Summary of Contents for Sawmill LT20 AC MH Series











































































































Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands

Wood-mizer Sawmill LT20 AC MH Series, Safety, Setup, Operation & Maintenance Manual

Search results

Summary of Contents for Sawmill LT20 AC MH Series

Reviews:

Related manuals for Sawmill LT20 AC MH Series

Brands by name

Popular brands