Wolf E Series Service Manual Download Page 54

Page: 54 / 59

Page 54

Error Code

Error

Possible Cause

Test/Action

E71/F21

Short circuit in the

drive motor for the

water tank.

Check the wiring of the drive motor for the water

tank.

Replace the valve assembly.

Replace the relay board.

E72/F21

Open circuit in the

drive motor of the

water tank.

Check the wiring of the drive motor for the water

tank.

Replace the valve assembly.

Replace the relay board.

E74/F22

Retractable door

handle not initialized.

Sequence errors E74,

E75, E76, and E77.

See E74, E75, E76, or E77.

E75/F22

Retractable door

handle switch.

Switch on drive board

defective or not

mounted correctly.

Inspect the retractable handle drive.

Replace the retractable handle drive.

E76/F22

Short circuit retractable

door handle drive.

Check the wiring of the retractable door handle

drive.

Replace the retractable door drive.

Replace the relay board.

E77/F22

Open circuit retractable

door handle drive.

Check the wiring of the retractable door handle

drive.

Replace the retractable door drive.

Replace the relay board.

E78/F24

Sump pumping off

error.

Not applicable to Wolf products.

E79/F27

Water inlet is not tight.

Not applicable to Wolf products.

E80

Feed tank is not tight.

Not applicable to Wolf products.

E81/F23

Evaporator draining

error.

Level measure pin not

sensing the correct

level for the following

reasons:
Faulty level measure

pin.
Scale on the

evaporator is heavy.
The evaporator is full of

descaling solution.
The valve evaporator is

defective.
The drain pump is

defective.
A short circuit in the

drain pump or level

measure pin wiring.

Descale the unit.

Manually drain the evaporator.

Measure the resistance of the drain pump and

valve evaporator.

Check for a short circuit to the drain pump or

valve evaporator.

Replace the level measure pin.

Replace the relay board.

Replace the control board.

E82/F10

Water leak in sump.

Not applicable to Wolf products.

E84

Slider not initialized.

Sequence errors E85,

E86, and E87.

See E85, E86, or E87.

E85/F4

Short circuit in stepper

motor.

Inspect the stepper motor wiring.

Measure the resistance of the stepper motor.

Replace the stepper motor.

Replace the relay board.

E86/F4

Open circuit in the

stepper motor.

Inspect the stepper motor wiring.

E Series SO24 (SWS 13543126)

Troubleshooting

Troubleshooting Guide

service.subzero.com

827705 REVA 01/2019

Summary of Contents for E Series




























































Search results

Summary of Contents for E Series

Reviews:

Related manuals for E Series

Brands by name

Popular brands

Wolf E Series, Service Manual

Search results

Summary of Contents for E Series

Reviews:

Related manuals for E Series

Brands by name

Popular brands