Wolf E Series Service Manual Download Page 38

Page: 38 / 59

Page 38

Remove the Exhaust Vent

Use a T-20 Torx bit to remove the screws from the exhaust
vent guide.

Lift the exhaust vent guide and exhaust vent arm slightly.

Pull the exhaust vent down from the exhaust vent arm.

Remove the exhaust vent from the unit.

EXHAUST VENT INSTALLATION

After installing the exhaust vent, install:

Install the Exhaust Vent

Place the exhaust vent inside the exhaust fan opening.

Insert the exhaust vent guide and exhaust vent arm into the
hole.

Push the exhaust vent on the exhaust vent arm.

Use a T-20 Torx bit to install the screws into the exhaust
vent guide.

EXHAUST FAN RESISTOR REMOVAL

WARNING

Turn off the power to the product before starting this
procedure.

To remove the exhaust fan resistor, first

uninstall the unit

, and

remove:

Top cover

Remove the Exhaust Fan Resistor

Disconnect the wire connectors from the exhaust fan
resistor.

Use a T-20 Torx bit to remove the screw from the exhaust
fan resistor.

Remove the exhaust fan resistor from the unit.

EXHAUST FAN RESISTOR INSTALLATION

After installing the exhaust fan resistor, install:

Top cover

Then

install the unit

Install the Exhaust Fan Resistor

Place the exhaust fan resistor in the unit.

Use a T-20 Torx bit to install the screw into the exhaust fan
resistor.

Connect the wire connectors to the exhaust fan resistor.

E Series SO24 (SWS 13543126)

Top Component Removal and Installation

service.subzero.com

827705 REVA 01/2019

Summary of Contents for E Series




























































Search results

Summary of Contents for E Series

Reviews:

Related manuals for E Series

Brands by name

Popular brands

Wolf E Series, Service Manual

Search results

Summary of Contents for E Series

Reviews:

Related manuals for E Series

Brands by name

Popular brands