manualshive.com logo in svg

Wolf E Series, Service Manual

Share
Download
Wolf E Series Service Manual Download Page 55

Page 55

Error Code

Error

Possible Cause

Test/Action

2

Measure the resistance of the stepper motor.

3

Replace the stepper motor.

4

Replace the relay board.

E87/F4

Slider blocked.

Slider path restricted

during operation.

1

Slider blocked with grease.

2

Slider mechanism is too tight. Replace the slider.

E88

Slider in stop position.

Slider path restricted

during operation.

1

Slider blocked with grease.

2

Slider mechanism is too tight. Replace the slider.

E89/F18

Communication

interruption - inverter.

Not applicable to Wolf products.

E90/F18

The temperature

reading of the inverter

heat sink is defective.

Not applicable to Wolf products.

E91/F18

Temperature

measurement of

magnetron defective.

Not applicable to Wolf products.

E92/F18

Magnetron heating coil

defective.

Not applicable to Wolf products.

E93/F18

Defective microwave

anode distance

system.

Not applicable to Wolf products.

E94/F19

Inverter hardware

defective.

Not applicable to Wolf products.

E95/F18

Insufficient cooling of

magnetron.

Not applicable to Wolf products.

E97

Operating system:

Watchdog control

board.

Replace the control board.

E98

Operating system:

Watchdog relay board.

Replace the relay board.

E99

Operating system:

ASSERT control board.

Moisture on control

board.

1

Inspect the control board for moisture.

2

Replace the control board if the error continues.

E100

Operating system:

ASSERT relay board.

Moisture on relay

board.

1

Inspect the relay board for moisture.

2

Replace the relay board if the error continues.

E101/F30

No communication

with control board.

1

Inspect the connection between the relay board

and control board.

2

Replace the control board.

3

Replace the relay board.

E102/F30

No communication

with relay board.

1

Inspect the connection between the relay board

and control board.

2

Replace the relay board.

3

Replace the control board.

E103/F31

Operating system:

Communication

between relay board

and control board is

incompatible.

Software version of

relay board and control

board incompatible.

1

Reload the software.

2

Replace the control board and relay board.

E104/F31

Operating system:

CORE incompatible.

Reload software.

E105

Operating system:

NVRAM-FLASH-PAGE

write error.

Moisture on control

board.

1

Inspect the control board for moisture.

2

Replace the control board if the error continues.

E106

Operating system:

NVRAM-FLASH-PAGE

delete error.

Moisture on control

board.

1

Inspect the control board for moisture.

E Series SO24 (SWS 13543126)

Troubleshooting

Troubleshooting Guide 

service.subzero.com

827705 REVA     01/2019

54

 

Summary of Contents for E Series




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands