Wolf Garten PS 20 eM, Operating Instructions Manual

Page: 29 / 271

Safety information
EN
29
¾
If you are setting the tool down, always
ensure that the motor is turned off.
¾
Every time you move to a different location,
turn the motor off and fit the protective cover.
¾
Never use the tool in a wet or moist
environment .
¾
Only use chains and bars approved by the
manufacturer .
¾
Be aware of chainsaw kickback and prevent
the guide bar tip from contacting objects . Do
not cut with the tip of the guide bar .
Information about vibrations:
¾
Vibrations can cause nerve damage and
impair the blood circulation in the hands and
arms .
¾
When working in the cold, wear warm
clothing and keep your hands warm and dry .
¾
Take breaks .
It has been reported that vibration from hand-
held power tools can contribute to a condition
called Raynaud’s Syndrome (white finger
syndrome) in certain individuals. White finger
syndrome is a vascular disorder in which
tiny blood vessels in the fingers and toes
suddenly contract . The areas concerned no
longer receive a sufficient blood supply and
consequently appear extremely pale .
Frequent use of vibrating tools by persons with
poor blood circulation (e .g . smokers, diabetics)
can cause nerve damage . If you notice any
unusual pains or adverse effects, stop work
immediately and see a doctor . Therefore,
if you are a long-term or regular user, it is
recommended that you carefully monitor the
state of your hands and fingers. Visit a doctor
immediately if any of the above symptoms
occur . Observe the following instructions to
reduce the hazards:
1. Keep your body warm, especially your hands,
particularly in cold weather.
2. Take regular breaks and use the opportunity
to move your hands around to increase the
circulation. Always maintain a tight grip, but do
not constantly hold the handles with excess
pressure.
3. Limit the length of use of high-vibration tools
per day and spread the use over several
days. Prepare a work schedule that limits the
vibration load.
4. Ensure as small as possible vibration of the
tool by regular servicing and ensuring parts
are firmly attached to it. Replace used parts
and components immediately.
5. Regularly change your working position.
6. If the machine is used more frequently, you
should contact your dealer and procure anti-vi-
bration equipment (handles) as required.
¾
The specified vibration emission values:
• Were measured according to a standardised
testing procedure.
• Make it possible to estimate the power tool
emissions and compare these with different
power tools. Dependent on the conditions of
use, the state of the power tool or the tools
inserted into it for use, the actual load may be
higher or lower. When estimating the emis-
sions, take into account work breaks and
phases when the tool is under reduced load.
Define protective actions, e.g. organisational
measures, based on appropriately adapted
estimates.
After use
¾
Switch the device off, remove the operating
arm from the device and check the device for
damage . Attention, danger! Cutting tool still
running!
¾
If you need to clean or service the device,
switch it off and remove the operating arm.
Attention, danger! Cutting tool still running!
¾
Always wait until the cutting tool comes to
a standstill and do not touch any moving
dangerous parts without first removing the
operating arm from the device .
¾
Removal of the protective equipment must
only be performed with the motor stationary
and the operating arm removed .
¾
Ensure that ventilation slots are free from dirt .
¾
Do not clean the device with water .
¾
Store the device in a secure location .
¾
Store the device out of reach of children .
¾
Let the device cool down before putting it
away and/or storing it .
¾
Always fit the protective cover after use and
when not using .
General safety information
¾
Spare parts must meet the requirements of
the manufacturer . Therefore, use only original
spare parts or those spare parts authorised by
the manufacturer. During replacement, always
observe the supplied fitting instructions and
always remove the operating arm from the device
prior to use.
¾
Repairs must only be performed by a
qualified technician or service centre.
Specialist workshop addresses can be found on
our website.
¾
This pole saw is intended for the care of trees
in private households . The device must not
be used for purposes other than those intended
because of the risk of bodily injury to the user or
other persons.
Safety information