WinGD X72-B Operation Manual Download Page 353

Page: 353 / 526

PROCEDURE

Make sure that the auxiliary systems continue to operate.

If possible, keep the cooling water warm to prevent too much temperature decrease of the
engine.

Open the indicator valves in the cylinder covers.

Engage the turning gear.

WARNING

Injury hazard. Before you operate the turning gear, make sure that no personnel are near
the flywheel, or in the engine.

Operate the turning gear for a short period at the intervals that follow:

•

Daily in damp climate

•

Weekly in usual climate.

Stop the turning gear so, that the pistons stop in different positions each time.

CLOSE UP

•

None

X72-B

AA00-0000-00AAA-151A-A

Operation Manual

Prepare the engine for a short service break

Winterthur Gas & Diesel Ltd.

- 353 -

Issue 003 2021-12

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Search results

Summary of Contents for X72-B

Reviews:

Related manuals for X72-B

Brands by name

Popular brands

WinGD X72-B, Operation Manual

Search results

Summary of Contents for X72-B

Reviews:

Related manuals for X72-B

Brands by name

Popular brands