WinGD X72-B Operation Manual Download Page 520 | Manualshive

Page: 520 / 526

background image

12.4.8

Fuel Additives

WinGD does not recommend the use of fuel additives. Additives are not necessary for fuels that
obey the ISO 8217:2017 standard or for fuels that WinGD has recommended.

If you think that it is necessary to use additives, WinGD recommends to speak to the fuel supplier
and to the additive supplier. They can give you the related results of the use of additives. If you
use additives for some causes, you assume full responsibility. Existing No Objection Letters done
by Wärtsilä Switzerland Ltd. are no longer applicable and have no more support by WinGD.

NOTE:

WinGD does not accept liability or responsibility for the performance or potential damage
caused by the use of such additives.

12.4.9

Non-standard fuels

If it is necessary to use non-standard fuels (fuels that are not in the related list from WinGD), speak
to or send a message to WinGD before use.

NOTE:

WinGD does not accept liability or responsibility for the performance or potential damage
caused by the use of non-standard fuels.

X72-B

AA00-0000-00AAA-030A-A

Operation Manual

Diesel engine fuels

Winterthur Gas & Diesel Ltd.

- 520 -

Issue 003 2021-12

«
...
518
519
520
521
522
...
»

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X72-B

Brand: JetCat Pages: 54

Brand: FeiaoModel Pages: 7

Brand: Nanni Pages: 110

Brand: Nanni Pages: 32

Brand: Jenny Science Pages: 9

Brand: Sole Diesel Pages: 40

695D/925 Series

Brand: Wisco Industries Pages: 6

Brand: MTU Pages: 239

GARDEN SNOWBUSTER (160F)

Brand: Texas Pages: 33

HYDRO-FORCE 65043

Brand: Bestway Pages: 8

Brand: Volvo Penta Pages: 90

Brand: Volvo Penta Pages: 108

Brand: Baumuller Pages: 34

Brand: HELIX Pages: 18

Brand: DLE Pages: 5

Brand: Briggs & Stratton Pages: 100

Brand: HKS Pages: 49

AM-EN2211-S103 Series

Brand: Assun Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands