Westfield WCX 1335 Assembly Manual Download Page 46 | Manualshive

Page: 46 / 62

background image

46

30998 R1

3. Loosely secure motor mount bracket (1) and 10" hitch ring (2) onto the conveyor tube using six 7/16" x 1"

bolts (3) and 7/16" locknuts (4).

Note

Orient the motor mount bracket precisely as shown in

Figure 34

.

4. Attach the motor mount (5) to the motor mount bracket using hinge rod (6) and 1/8" x 1-1/2" cotter pin (7)

(see

Figure 35

).

5. Level the motor mount with adjust bolt (8) and 5/8" hex nut (9).

6. Using a level, rotate the hitch ring until the motor mount and bracket are level with the track.

7. Tighten all bolts and locknuts.

Table 24.

Drive Mount Components

Item

Description

1

Motor Mount Bracket

2

10" Hitch Ring

3

7/16" x 1" Bolt

4

7/16" Locknut

5

Motor Mount

6

Hinge Rod

7

1/8" x 1-1/2" Cotter Pin

8

Adjust Bolt

9

5/8" Hex Nut

4. ASSEMBLY

WCX 1335 TOP-DRIVE CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

«
...
44
45
46
47
48
...
»

Summary of Contents for WCX 1335































































Reviews:

No comments

Related manuals for WCX 1335

Brand: LAUMAS Pages: 40

Brand: Panasonic Pages: 132

EASA-PHONE KX-T30810

Brand: Panasonic Pages: 16

Brand: Gainsborough Pages: 2

Brand: i-onik Pages: 6

Brand: Xerox Pages: 2

KTS-WB61141142 Series

Brand: SICK Pages: 8

Brand: Stobag Pages: 3

PowerPack TPB-2112

Brand: texet Pages: 16

Brand: AIA Pages: 8

Brand: Eco Pages: 34

Brand: Brodit Pages: 2

Brand: GameSir Pages: 22

Brand: Nav TV Pages: 5

Brand: Naterial Pages: 124

Brand: Whispbar Pages: 15

Brand: tams elektronik Pages: 44

Brand: U.S. General Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands