Westfield WCX 1335 Assembly Manual Download Page 28 | Manualshive

Page: 28 / 62

background image

28

30998 R1

Figure 13.

Fish Tape Connected to a Short Piece of Belt

Thread the Conveyor Belt

1. From the spout end, pull the fish tape until the belt emerges from the spout.

Figure 14.

Conveyor Belt Pulled Through the Spout

2. Wrap the belt around the spout roller and pull it back under the conveyor tube to the hopper until

approximately 6' (1.8 m) of excess belt remains on the stand behind the hopper.

3. Wrap the remaining conveyor belt around the hopper roller (7) and under the tube.

4. ASSEMBLY

WCX 1335 TOP-DRIVE CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

«
...
26
27
28
29
30
...
»

Summary of Contents for WCX 1335































































Reviews:

No comments

Related manuals for WCX 1335

and Vantage Pro

Brand: DAVIS Pages: 4

and Vantage Pro

Brand: Davis Instruments Pages: 4

Brand: Datavideo Pages: 45

Brand: RaceChip Pages: 12

BIM-BAM GNS-921

Brand: e2 elektro Pages: 2

Brand: Jabra Pages: 7

Brand: Jabra Pages: 2

Brand: Jabra Pages: 12

Brand: wattio Pages: 15

Brand: Razor Pages: 2

RAZORX LONGBOARD

Brand: Razor Pages: 16

Brand: RayTek Pages: 93

Brand: Vaisala Pages: 24

Brand: Waldbeck Pages: 7

Aerasgard KCO2-W

Brand: S+S Regeltechnik Pages: 16

Brand: NavLinkz Pages: 4

Brand: Berlebach Pages: 2

Brand: Moza Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands