Westfield WCX 1335 Assembly Manual Download Page 13

Page: 13 / 62

30998 R1

Table 1.

Safety Decals

Part Number

Description

20817

To prevent death or serious injury:

• When operating or moving, keep equipment away from

overhead power lines and devices.

• Fully lower equipment before moving.

This equipment is not insulated.
Electrocution can occur without direct contact.

ELECTROCUTION HAZARD

DANGER

20811

To prevent death or serious injury:

UPENDING HAZARD

WARNING

• Anchor intake end and/or support

discharge end to prevent upending.

• Intake end must always have downward

weight. Do not release until attached to

tow bar or resting on ground.

• Do not raise intake end above tow bar

height.

• Empty conveyor and fully lower before

moving.

WCX 1335 TOP-DRIVE CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

2. SAFETY

Summary of Contents for WCX 1335































































Search results

Summary of Contents for WCX 1335

Reviews:

Related manuals for WCX 1335

Brands by name

Popular brands

Westfield WCX 1335, Assembly Manual

Search results

Summary of Contents for WCX 1335

Reviews:

Related manuals for WCX 1335

Brands by name

Popular brands