Westfield WCX 1335 Assembly Manual Download Page 38 | Manualshive

Page: 38 / 62

background image

38

30998 R1

Figure 26.

Installing Spout Hood

4.15. Assemble the Wheel Hub

1. Remove any dirt or paint from the spindle of the axle (1) and hub (4).

2. Thoroughly pack the wheel bearings (3, 5) and cups with a good grade of bearing grease.

3. Place the large bearing (3) into the hub (4) and carefully tap in seal (2).

4. Slip the hub onto the axle spindle and insert the small bearing (5).

5. Tighten 3/4" slotted nut (6) until hub drags slightly. Back off nut about 1/4" turn until the hub turns freely.

6. Install 1/8" x 1-1/2" cotter pin (7) and dust cap (8).

Table 18.

Wheel Hub Components

Item

Description

1

Axle Weldment

2

Seal

3

Large Bearing

4

Hub

5

Small Bearing

6

3/4" Slotted Nut

7

1/8" x 1-1/2" Cotter Pin

8

Dust Cap

2

1

4

3

3

4

4. ASSEMBLY

WCX 1335 TOP-DRIVE CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

«
...
36
37
38
39
40
...
»

Summary of Contents for WCX 1335































































Reviews:

No comments

Related manuals for WCX 1335

Brand: Unex Pages: 24

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

BIESEMEYER 78-955

Brand: Delta Pages: 12

Brand: Zipp Pages: 39

Brand: Danfoss Pages: 4

Brand: Fronius Pages: 56

Brand: Hyena Pages: 13

Brand: Kolpin Pages: 25

Brand: Cargo Floor Pages: 16

Brand: Deka Pages: 4

BIS M-411-068-001-09-S72

Brand: Balluff Pages: 2

Inflatable Stand Up Paddle Board

Brand: Kings Adventure Pages: 3

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

MOBILE COOLING TROPICOOL TC07

Brand: Dometic Pages: 156

Brand: PROAIM Pages: 3

Brand: PCB Piezotronics Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands