WERKU WK501360, Original Instructions Manual

Page: 2 / 40

2
English
ENG
CE DECLARATION CONFORMITY.
►
Werku ® declares that the WK501360 airless
gun is in accordance with the European
Directives and Standards 2006/42/CE and
EN12621:2006+A1:2010.
La Coruña, 01/11/2020.
R Yáñez
Werku Tools SA
TECHNICAL CHARACTERISTICS.
►
Airless pump >1 HP (750 W)
►
Working pressure
90-210 bar
►
Maximum pressure 310 bar
►
RAC-
XHD tip
►
Inlet thread NPS 3/8”
►
Outlet thread
BSP 7/8”
►
Working temperature 5-40ºC
►
Material
temperature <43ºC
►
Net weight 0.380 kg
►
Acoustic
pressure LpA <89 dB(A)
►
Acoustic pressure LwA
<90.82 dB(A)
►
Vibration Ah <0.715 m/s².
SAFETY INSTRUCTIONS.
►
Read all security warnings and all instructions
►
Failure to follow all warnings and instructions
listed below may result in electrical shock, fire
and/or serious injury
►
Keep all warnings and
all instructions for future reference
►
Accidents
can be avoided in many cases by recognizing a
potentially hazardous situation before it occurs and
by observing appropriate safety procedures
►
Do
not use this airless gun for other applications than
those specified in this manual.
SAFETY PRECAUTIONS.
►
Be safety-conscious
►
All local and national
regulations governing ventilation, fire prevention,
and operation must be observed
►
Hazard:
Injection injury
►
A high pressure stream produced
by this airless gun can pierce the skin and
underlying tissues, leading to serious injury and
possible amputation
►
Do not treat an injection
injury as a simple cut
►
Injection can lead to
amputation
►
See a physician immediately
►
Inform the physician of the type of coating
material or cleaning agent with which the injury
was caused
►
The maximum operating range of
this airless gun is 310 bar fluid pressure
►
Never
aim the airless gun at any part of the body
►
Never
allow any part of the body to touch the fluid stream
►
Do not allow body to touch a leak in the fluid
hose
►
Never put hand in front of the airless gun
►
Gloves will not provide protection against an
injection injury
►
Never point the airless gun at
anyone else
►
Always lock the airless gun trigger,
shut the pump off and release all pressure before
servicing, cleaning the tip or guard, changing
tip, or leaving unattended
►
Pressure will not be
released by turning off the motor
►
The prime/
spray valve must be turned to prime to relieve the
pressure
►
Refer to the pressure relief pressure
described in the pump manual
►
Always keep the
tip guard in place while spraying
►
The tip guard
provides some protection but is mainly a warning
device
►
Always remove the spray tip before
flushing or cleaning the system
►
The hose can
develop leaks from wear, kinking and abuse
►
A
leak can inject material into the skin
►
Inspect
the hose before each use
►
Never use an airless
gun without a trigger lock and trigger guard in
place and in good working order
►
All accessories
must be rated at or above the maximum
operating pressure range of the airless gun
►
This includes spray tips, extensions and hose
►
Hazard: Explosion hazard due to incompatible
materials will cause severe injury or property
damage
►
Do not use materials containing
bleach or chlorine
►
Do not use halogenated
hydrocarbon solvents such as bleach, mildewcide,
methylene chloride trichloroethane
►
They are
not compatible with aluminum
►
Contact your
coating material supplier about the compatibility
of material with aluminum
►
Hazard: General
►
This airless gun can cause severe injury or
property damage
►
Read all instructions and
safety precautions before operating this airless
gun
►
Never spray near sources of ignition; eg
open flames, cigarettes (also cigars and pipes
are sources of ignition), sparks, hot wires and
hot surfaces, etc
►
Wear respiratory equipment
when spraying
►
The operator must be provided
with a protective mask
►
In order to prevent work
related illness, the manufacturer’s regulations
for the materials, solvents, and cleaning agents
used must be observed when preparing, working
with and cleaning the airless gun
►
Protective