WELLTECH WPoE-2426 User Manual Download

Page: 15 / 280

Publication date: August, 2012

Revision 1.0

Step2.

If the device is a network card and the switch is in the wiring closet, attach the

other end of the cable segment to a modular wall outlet that is connected to

the wiring closet. (See the section “Network Wiring Connections.”) Otherwise,

attach the other end to an available port on the switch.

Make sure each twisted pair cable does not exceed 100 meters (328 ft) in length.

OTE

Avoid using flow control on a port connected to a hub

unless it is actually required to solve a problem. Otherwise

back pressure jamming signals may degrade overall

performance for the segment attached to the hub.

Step3.

As each connection is made, the Link LED (on the switch panel) corresponding

to each port will light green (1000 Mbps) or amber (100 Mbps) to indicate that

the connection is valid.

NETWORK WIRING CONNECTIONS

Today, the punch-down block is an integral part of many of the newer equipment racks.

It is actually part of the patch panel. Instructions for making connections in the wiring

closet with this type of equipment are as follows.

Step1.

Attach one end of a patch cable to an available port on the switch, and the

other end to the patch panel.

Step2.

If not already in place, attach one end of a cable segment to the back of the

patch panel where the punch-down block is located, and the other end to a

modular wall outlet.

Step3.

Label the cables to simplify future troubleshooting. See “

Cable Labeling and

Connection Records

” on page 29

Figure 17: Network Wiring Connections

Switch

Equipment Rack
(side view)

Patch Panel

Patch-Down Block

Wall

Summary of Contents for WPoE-2426

























































































































































































































































































Search results

Summary of Contents for WPoE-2426

Reviews:

Related manuals for WPoE-2426

Brands by name

Popular brands

WELLTECH WPoE-2426, User Manual

Search results

Summary of Contents for WPoE-2426

Reviews:

Related manuals for WPoE-2426

Brands by name

Popular brands