background image

4427 Dawson Street 

Burnaby, B.C., Canada V5C 4B8 

Office: 604.502-9007 

Fax: 604.502-9044 

Web: 

www.webbelectronicsinc.com

 

 
 

 

 
Document Name:  MWP-302 User Manual 

1 7   o f   1 7  

CONFIDENTIAL, Copyright © 2018 

This document is proprietary to Webb Electronics Inc. It may not be copied or otherwise 
distributed without the express consent of Webb Electronics Inc.

 

If this equipment causes harm to the telephone network, the telephone company will notify you in advance 
that temporary discontinuance of service may be required. If advance notice isn’t practical, the telephone 
company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint 
with the FCC if you believe it is necessary. 

 

The telephone company may make changes in its facilities, equipment, operations, or procedures that could 
affect the operation of the equipment. If this happens, the telephone company will provide advance notice 
for you to make the necessary modifications to maintain uninterrupted service. 

 

If experiencing trouble with this equipment, please contact the Technical Support Center at 
Webb Electronics Inc. for warranty and/or repair information. If the trouble is causing harm to 
the telephone network, the telephone company may request you to remove the  equipment 
from the network until the problem is resolved. 

 

This equipment cannot be used on public coin service provided by the telephone company. 

Connection  to  party  lines  is  subject  to  state  tariffs.  Contact  your  state  public  utilities 
commission for information. 

 

This equipment does not provide data operation. 

 

JACK (USOC): RJ11C 

RINGER EQUIVALENCE = 0.8 Class B 

 

 

CANADA CERTIFICATION

 

 

NOTICE: 

This product meets the applicable Innovation, Science and Economic Development Canada technical 

specifications This is confirmed by the registration number.  The  abbreviation, IC, before the registration number 
signifies that registration was performed based on a Declaration of Conformity indicating that Innovation, Science 
and Economic Development Canada (ISED) technical specifications were met. It does not imply that ISED approved 
the equipment. 

 

NOTICE

:

 

The Canadian Ringer Equivalence Number (REN) for this equipment is: 0.1. The REN assigned to each 

terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone 
interface. The termination on an interface may consist of any combination of devices subject only to the requirement 
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. 
 
 

 

 

 

 

 

WEBB ELECTRONICS INC.

 

Canada

:  Vancouver, Toronto, Montreal 

 

Toll Free

:  1-877-731-1010

 

Fax

:  1-877-731-1028 

Technical Support

:  [email protected] 

Web Site

:  www.webbelectronicsinc.com 

 

 

 

Summary of Contents for MWP-302



















Reviews: