WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452 Operating Manual Download Page 160

Page: 160 / 217

Wärtsilä JOVYSTAR COMPACT L

BAX 5624

- 25 -

9.2 Backfeed Protection Device

The UPS is provided (as option) with voltage-free contacts, which can be used to operate the shunt

trip coil (undervoltage release type) of the external sectioning device; the external device is not part of

the UPS supply and is provided and installed at customer care.

The following table shows the main electrical characteristics of the external sectioning device.

Backfeed protection device

Power (kVA)

200

Maximum operating voltage

(Vac)

690

Minimum rated current (A)

400

Summary of Contents for JOVYSTAR COMPACT S BAX 5452


























































































































































































































Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Related manuals for JOVYSTAR COMPACT S BAX 5452

Brands by name

Popular brands

WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452, Operating Manual

Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Related manuals for JOVYSTAR COMPACT S BAX 5452

Brands by name

Popular brands