WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452 Operating Manual Download Page 42

Page: 42 / 217

Wärtsilä JOVYSTAR COMPACT S

BAX 5452

42 -

Alarm

A45 HIGH SSW TEMPERATURE

Description

High temperature of the static switch heat sink.

Possible causes Fault of the heat sink cooling fans.

The room temperature or cooling air temperature is too high.

Solutions

1. Check the fans operation.

2. Clean the ventilation grids and the air filters, if any.

3. Check the air conditioning system (if present).

4. If the alarm persists, contact our Technical Support Service.

Alarm

A46 REDUNDANCY LOSS

Description

This alarm is only active on parallel systems. Continuity is not ensured in the event of a fault on one of the UPS units.

Possible causes The total load is higher than the maximum expected value.

Possible failure on the measuring circuit.

Solutions

1. Check the load fed by the system.

2. If the alarm persists, contact our Technical Support Service.

Alarm

A47 WRONG TRANSMISSION OF EEPROM PARAMETERS

Description

Internal error.

Possible causes Microcontroller communication problems.
Solutions

1. Contact our Technical Support Service.

Alarm

A48 FAILED RECEPTION OF EEPROM PARAMETERS

Description

Internal error.

Possible causes Microcontroller communication problems.
Solutions

1. Contact our Technical Support Service.

Alarm

A49 TEST MODE DISCREPANCY

Description

Internal error.

Possible causes Microcontroller communication problems.
Solutions

1. Contact our Technical Support Service.

Alarm

A50 STATIC SWITCH BLOCKED

Description

The static switch is blocked. The load is no longer supplied.

Possible causes Loads failure.

Possible UPS fault.

Solutions

1. Check the loads for possible failures.

2. Reset the system.

3. If the alarm persists, contact our Technical Support Service.

Alarm

A51 BATTERY TEMPERATURE OUT OF TOLERANCE

Description

The battery temperature is out of tolerance. This alarm is only active when the temperature probe is installed and

enabled on the battery.

Possible causes Anomalous temperature in the battery cabinet.

Possible failure on the measuring circuit.

Solutions

1. Check the temperature on the batteries and remove the cause of the alarm, if any.

2. If the alarm persists, contact our Technical Support Service.

Alarm

A52 DC COMP ERROR

Description

Internal error.

Possible causes Microcontroller communication problems.
Solutions

1. Contact our Technical Support Service.

Alarm

A53 FIRMWARE CONFIGURATION ERROR

Description

The controller has detected an incompatibility in the control software.

Possible causes The software update was not performed properly.
Solutions

1. Contact our Technical Support Service.

Alarm

A54 PARALLEL CAN COMMUNICATION ERROR

Description

Internal error.

Possible causes Microcontroller communication problems.
Solutions

1. Contact our Technical Support Service.

Alarm

A55 PARALLEL CABLE DISCONNECTED

Description

Parallel cable doesn’t communicate.

Possible causes Parallel cable disconnected or damaged.

Solutions

1. Check the connection of all cable.

2. Contact our Technical Support Service.

Alarm

A56 MAINS BALANCE

Description

Rectifier stop at unbalanced mains

Possible causes The voltages of the three phases are deviate from each other about 7 %.

Solutions

1. Check the input voltages/- cable from the mains.

2. Contact our Technical Support Service.

Summary of Contents for JOVYSTAR COMPACT S BAX 5452


























































































































































































































Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Brands by name

Popular brands

WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452, Operating Manual

Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Brands by name

Popular brands