manualshive.com logo in svg

WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452, Operating Manual

Share
Download
WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452 Operating Manual Download Page 39

 

Wärtsilä JOVYSTAR COMPACT S 

BAX 5452 

 - 

39 -

 

 

Alarm 

A11  SHORT-CIRCUIT 

Description 

The current sensor has detected a short-circuit at the output. 

Possible causes 

Load problem. 
Measuring circuit failure. 

Solutions 

1. Check the loads connected to the UPS output. 

2. If the alarm persists, contact our Technical Support Service. 

Alarm 

A12  SHORT-CIRCUIT TIMEOUT STOP 

Description 

Inverter shutdown due to an extended short-circuit during a power failure, or due to an over current on the inverter 

bridge input. 

Possible causes 

Short-circuit on the loads during a power failure. 

Inverter bridge fault. 

Temporary current peak. 

Solutions 

1. Reset the system. 

2. If the alarm persists, contact our Technical Support Service. 

Alarm 

A13  INVERTER OUT OF TOLERANCE 

Description 

The inverter voltage or frequency is out of tolerance. 

Possible causes  Inverter shutdown due to an alarm. 

Inverter failure. 

Solutions 

1. Check which alarms are present and carry out the indicated procedures. 

2. If the alarm persists, contact our Technical Support Service. 

Alarm 

A14  BYPASS PHASE ROTATION NOT CORRECT 

Description 

The phase rotation of the bypass line is wrong. 

Possible causes  Wrong connection of power cables. 

Solutions 

1. Check the phase rotation. 

2. If the alarm persists, contact our Technical Support Service. 

Alarm 

A15  BYPASS FAILURE 

Description 

The voltage or frequency of the bypass line is out of tolerance. 

Possible causes  Bypass line instability or failure. 

Wrong phase rotation. 

Solutions 

1. Check the connections to the mains. 

2. Check the stability of mains voltage. 

3. If the alarm persists, contact our Technical Support Service. 

Alarm 

A16  BYPASS FEEDS LOAD (Only in Online-mode) 

Description 

The load is fed by the bypass line. 

Possible causes  Temporary changeover due to inverter failure. 

Solutions 

1. Verify the inverter status and check whether other alarms are present. 

2. If the alarm persists, contact our Technical Support Service. 

Alarm 

A17  RE-TRANSFER BLOCKED 

Description 

The load is blocked on the bypass line. 

Possible causes  Very frequent changeovers due to load in-rush currents. 

Static switch problems. 

Solutions 

1.   Reset the system. 

2.   Check the in-rush currents of the loads. 

3.   If the alarm persists, contact our Technical Support Service. 

Alarm 

A18  MBCB CLOSED  

Description 

The manual bypass isolator is closed. 

Possible causes  Manual bypass isolator closed. 

Solutions 

1. Check the status of the manual bypass isolator. 

2. Check the functionality of the auxiliary contact of the isolator. 

3. If the alarm persists, contact our Technical Support Service. 

Alarm 

A19  OCB OPEN 

Description 

The output isolator is open. 

Possible causes  Output isolator open. 

Solutions 

1. Check the status of the output isolator. 

2. Check the functionality of the auxiliary contact of the isolator. 

3. If the alarm persists, contact our Technical Support Service. 

Alarm 

A20  OVERLOAD 

Description 

The current sensor has detected an overload at the output. If the alarm persists, the thermal image protection will be 

activated (alarm A21). 

Possible causes  Output overload. 

Measuring circuit failure. 

Solutions 

1. Check the loads connected to the UPS output. 

2. Contact our Technical Support Service. 

 

 

Summary of Contents for JOVYSTAR COMPACT S BAX 5452


























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands