WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452 Operating Manual Download Page 144

Page: 144 / 217

Wärtsilä JOVYSTAR COMPACT L

BAX 5624

- 9 -

7 Safety Rules and Warnings
7.1 Use of the UPS

Congratulations on choosing a product from JOVYATLAS for the safety of your equipment. To obtain

the best performance from your JOVYSTAR COMPACT L 200 kVA UPS system (Uninterruptible

Power Supply), we suggest that you take your time to read the following manual.

The purpose of this manual is to give a short description of the parts composing the UPS and to guide

the installer or the user through the installation of the unit in its using environment.

The installer or the user must read and correctly perform the instructions included in the present

manual, with particular reference to the requirements regarding safety, in compliance with the current

regulations.

Read the technical documentation

Before installing and using the device, make sure you have read and understood all the

instructions contained in the present manual and in the technical supporting documentation.

Check the technical characteristics

Before carrying out any installation or start-up operation on the UPS, make sure its technical

characteristics are compatible with the AC supply line and with the output loads.

7.2 Special Safety Warnings
7.2.1 General warnings

The UPS is provided with various stickers with indications regarding specific dangers. These stickers

must be always well visible and replaced in case they are damaged.

The present documentation must be always available in proximity to the device. In case of loss we

recommend to request a copy to the manufacturer, whose details are available in the “Contacts”

section.

7.2.2 Personnel

Any operation on the UPS must be carried out by qualified personnel.

By qualified and trained person we mean someone skilled in assembling, installing, starting up and

checking the correct operation of the product, who is qualified to perform his/her job and has entirely

read and understood this manual, especially the part regarding safety. Such training and qualification

shall be considered as such, only when certified by the manufacturer.

7.2.3 Transport and handling

Avoid bending or deforming the components and altering the insulation distances while transporting

and handling the product.

Undistributed weight

The weight of the UPS is not uniformly distributed. Pay attention when lifting.

Summary of Contents for JOVYSTAR COMPACT S BAX 5452


























































































































































































































Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Related manuals for JOVYSTAR COMPACT S BAX 5452

Brands by name

Popular brands

WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452, Operating Manual

Search results

Summary of Contents for JOVYSTAR COMPACT S BAX 5452

Reviews:

Related manuals for JOVYSTAR COMPACT S BAX 5452

Brands by name

Popular brands