manualshive.com logo in svg

WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452, Operating Manual

Share
Download
WÄRTSILÄ JOVYSTAR COMPACT S BAX 5452 Operating Manual Download Page 131

Wärtsilä JOVYSTAR COMPACT M  

BAX 5480 

- 81 - 

 

Alarm 

A32 

EPO BUS CLOSED 

Description 

The system is blocked due to the activation of the emergency power off button. 

Possible 

causes  

  Activation of the (local or remote) emergency power off button. 

Solutions  

1. Release the emergency power off button and reset the alarm. 

2. If the alarm persists, contact our Technical Support Service. 

 

Alarm 

A33 

ASYMMETRIC LOAD 

Description 

The positive and negative voltages measured on the DC capacitors towards the 

middle point are different. 

Possible 

causes  

  Failure on the measuring circuit. 

  Fault of DC capacitors. 

Solutions  

1. Reset the system. 

2. If the alarm persists, contact our Technical Support Service. 

 

Alarm 

A34 

SERVICE REQUIRED 

Description 

A UPS check is necessary. 

Possible 

causes  

  UPS fault. 

Solutions  

1. If the alarm persists, contact our Technical Support Service. 

 

Alarm 

A35 

DIESEL MODE 

Description 

The UPS is supplied by the diesel generator. 

Possible 

causes  

  The auxiliary contact which activates the diesel generator connected to 

the UPS is closed, and imposes this operating mode. 

Solutions  

1. Wait for the diesel generator to stop as soon as the mains voltage is restored.  

2. Check the connection of the auxiliary contact which signals the diesel generator 

    start, to terminals XD1/XD2. 

3. If the alarm persists, contact our Technical Support Service. 

  

Alarm 

A36 

DC FASTSHUTDOWN 

Description 

Inverter shutdown due to the operation of the protection sensor as a result of 

sudden DC voltage variations.  

Possible 

causes  

  Battery fault. 

Solutions  

1. Check the battery. 

2. Reset the system. 

3. If the alarm persists, contact our Technical Support Service. 

 

Alarm 

A38 

INV --> LOAD 

Description 

The load is fed by the inverter. This alarm is active for UPS systems in “ECO” mode, 

where the preferential supply is from the bypass line. 

Possible 

causes  

  Temporary changeover due to bypass line failure. 

Solutions  

1. Verify the status of the bypass line and check whether other alarms are present. 

2. If the alarm persists, contact our Technical Support Service. 

 

Alarm 

A39 

INV ERROR LOOP 

Description 

The control is not able to regulate the inverter voltage precisely. 

Possible 

causes  

  Regulation system failure. 

Solutions  

1. Reset the system. 

2. If the alarm persists, contact our Technical Support Service. 

 

 

 

 

Summary of Contents for JOVYSTAR COMPACT S BAX 5452


























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands