Vollrath Stoelting Flavor Burst STL-80SS-DLX Operator'S Manual Download Page 64 | Manualshive

Page: 64 / 80

background image

61

7. Thread the 9-Tube Assembly coupler nut

onto the Lead’s casing and tighten to
secure.

NOTE:

THE 44-SYSTEMS WITH THE SPLIT

LEAD WILL CONNECT WITH THE TWO 9-
TUBE ASSEMBLIES OUTSIDE THE CABINET.

8. Gently lay the pump harness cable out and

away from the cabinet. Remove the open-
close bushing from the plate and wrap the
bushing around the pump harness cable
near the lower plate’s slotted hole. Snap
the grommet with the cable back into the
slotted hole in the plate.

Installing the Electronics Box and Power
Connections

The electronics box houses the electronics
board and most of the power connections for
the Deluxe unit. For shipping safety purposes,
the electronics box ships unconnected to the
unit. Follow these instructions to install the
electronics box to the back of the Deluxe
cabinet, connect the remaining power cables,
and power up the system.

1. Remove the electronics box cover by

unscrewing the 4 screws on each side.

2. Remove the two screw from the cover plate

and gently pull the plate away from the
electronics box. Leave the Drive Motor
cable connected to the board.

3. Insert the white plastic end of the pump

harness cable (from the back of the cabinet)
through the opening where the cover plate
was on the electronics box.

«
...
62
63
64
65
66
...
»

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

















































































Reviews:

No comments

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Saeco Poemia HD8325/08

Brand: Saeco Pages: 3

Brand: wacaco Pages: 7

Brand: knIndustrie Pages: 2

Brand: Welbilt Pages: 32

Brand: Caffitaly System Pages: 64

Brand: Russell Hobbs Pages: 8

Horizon Elite HC Series

Brand: Follett Pages: 52

Brand: V-ZUG Pages: 52

Brand: SEVERIN Pages: 1

Brand: Saeco Pages: 88

Brand: U-Line Pages: 43

Brand: Sunbeam Pages: 92

Brand: La San Marco Pages: 36

Brand: RTC Pages: 43

Brand: Jura Pages: 22

AQUAMATIK CM750 SERIES

Brand: Kenwood Pages: 28

Brand: Siemens Pages: 40

Brand: Siemens Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands