Vollrath Stoelting Flavor Burst STL-80SS-DLX Operator'S Manual Download Page 18

Page: 18 / 80

Syrup Pump and Related Parts (See Figure 5)

ITEM PART

NO.

DESCRIPTION

QTY.

FUNCTION

1 N/A

SOFT SERVE SYRUP PUMP
ASSEMBLY

Pumps syrup from flavor bags to flavor lines.

1A STOESYR307

PERISTALTIC SYRUP PUMP

1 ea. Pumps syrup from flavor bags to flavor lines.

1B STOETUB806

1/8” SYRUP PUMP REPL TUBE

1 ea. Transports syrup through pump.

1C STOEFAS2067

SYRUP PUMP TUBE WASHER-1/4

1 ea. Secures pump tube.

1D STOEFAS2066

SYRUP PUMP CLAMP-HOSE-1/4"

1 ea. Prevents pump tube from slipping.

1E STOEFAS2051

ROLLED FLANGE EYELET

1 ea. Creates tension for tighter fit.

1F STOEFIX1036

1/4" TO 1/4" OD UNION ELBOW

1 ea. Connects syrup in tube to pump.

1G STOEFIX1035

1/4 TO 3/16 OD REDUCING UNION

1 ea. Connects syrup pump to flavor line out.

2 STOESYR944

SYRUP TUBE ASSEMBLY –
SOFT SERVE

Transports flavor from bag to pump.

2A STOEFIX1054

1/4” ID HOSE BARB SHUTOFF

1 ea. Connects flavor line to flavor bag.

2B STOESYR902

FLAVOR-IN TUBE

1 ea. Carries syrup from syrup bag to pump.

2C STOETUB811

TUBE-SILICONE .188X.375 PE
FB80

1 ea. Connects barb fitment to tube port.

2D STOEFIX1048

FITTING-1/4X1/4 BARB FB80

1 ea. Connects syrup tube to silicone tube.

3 STOESYR927

INTERNAL 9-TUBE ASSEMBLY

Transports syrup from bags to flavor 9-Tube
Assembly.

3A STOESYR900

4' 9-TUBE ASSEMBLY TUBE

9 ea. Brings syrup from pump to Injector Head.

3B STOEROT511

LINE COUPLER NUT

1 ea.

Connects flavor lines to the internal
9-Tube Assembly.

3C STOEROT512

TUBE CONNECTOR BODY

1 ea.

Connects internal 9-Tube Assembly to
flavor lines.

3D STOEROT510

LINE COUPLER

1 ea.

Holds flavor lines in place.

3E STOEFAS2051

ROLLED FLANGE EYELET

9 ea. Secures flavor lines to line coupler.

3F STOEMIS3023

FLAVOR LINE DUST CAP

1 ea. Cover to protect end of flavor lines.

4 STOECAB113

FLAVORING TRAY

Houses syrup bags.

5 STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer
pumps.

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

















































































Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Operator'S Manual

Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands