Vollrath Stoelting Flavor Burst STL-80SS-DLX Operator'S Manual Download Page 32

Page: 32 / 80

5. Remove the Injector Assembly from the

Suspension bracket.

NOTE:

DO NOT

ATTEMPT TO REMOVE THE

SPOUT ADAPTER WITH THE ASSEMBLY
ATTACHED! USING THE ASSEMBLY OR
GEAR BOX AS LEVERAGE MAY BREAK THE
ADAPTER OR SPOUT OR DAMAGE THE
INJECTOR HEAD.

6. Remove the spout adapter from the freezer

spout.

NOTE:

YOU MAY USE A CLEAN, NARROW

TOOL (SUCH AS A SCREWDRIVER OR
OTHER STURDY ROD) TO GENTLY PRY
THE ADAPTER OFF. PLACE THE TOOL ON
THE ADAPTER PORT AND SLOWLY ANGLE
DOWN AGAINST THE FREEZER DOOR.

Disassembling the Injector Assembly

1. Rotate the Drive Motor to unlock and

remove the Motor from the Gear Box.

2. Rotate the Injector Head to unlock it from

the Gear Box.

3. Remove the Gear Cartridge from the Gear

Box.

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

















































































Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Operator'S Manual

Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands