Vollrath Stoelting Flavor Burst STL-80SS-DLX Operator'S Manual Download Page 12

Page: 12 / 80

Outer Cabinet (See Figure 2)

ITEM PART

NO.

DESCRIPTION

QTY.

FUNCTION

1 STOECAB237

CABINET TOP PANEL

Covers the top of the inner cabinet.

2 STOECAB235L

CABINET LEFT SIDE PANEL

Covers the left side of inner cabinet.

3 N/A

INNER CABINET ASSEMBLY

Houses syrup trays and bags.

4 STOECAB239

CABINET FRONT DOOR PANEL

Front door, allows access to flavor bags.

5 STOECAB256

FRONT DOOR HANDLE

Allows grip for opening front panel.

6 STOEFAS2014

8-32 X 1/2 PAN HEAD SCREW

Fastens the handle to front door panel.

7 STOERUB618

RUBBER BUMPER W/ WASHER

Provides spacing between cabinet base and
table.

8 STOEFAS2064

10-32 X 1/2" PAN HEAD SCREW

Fastens rubber bumpers to cabinet base.

9 STOEMIS3074

DUST CAP

Covers screw hole in rubber bumper.

10 STOECAB236TS

CABINET REAR PANEL

Allows access to pumps.

11 STOECAB235R

CABINET RIGHT SIDE PANEL

Covers right side of inner cabinet.

12 STOEMIS3150

FLAVOR BURST LOGO DECAL

Displays Flavor Burst trademark logo.

13 STOEFAS2024

8-32 X 1/4 PAN HEAD SCREW

Secures back panel to base.

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

















































































Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Operator'S Manual

Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands