Vollrath Stoelting Flavor Burst STL-80SS-DLX Operator'S Manual Download Page 14

Page: 14 / 80

Inner Cabinet (See Figure 3)

ITEM PART

NO.

DESCRIPTION

QTY.

FUNCTION

1 STOECAB201

SYRUP RACK COVER PANEL

Keeps side and inner panels stable.

2 STOECAB204L

SYRUP RACK LEFT PANEL

Holds outer syrup rails.

3 STOESYR945

SYRUP BAG CONNECTOR
ASSEMBLY – SOFT SERVE

Transports syrup from the bag to pumps.

4 STOECAB245

SYRUP TRAY RAIL

Holds flavor trays in place.

5 STOECAB145

TRAY SUPPORT BRACKET

Houses flavor line leading to syrup bag.

6 STOECAB203

SYRUP RACK DIVIDER PANEL

Holds inner syrup rails.

7 STOECAB202

SYRUP RACK BACK PANEL

Attaches the inner and side panels.

8 STOEMIS3028-80M

SANITIZER FLUSH TUBE
ASSEMBLY – SOFT SERVE INT

Flushes flavor lines with sanitizer when
attached.

9 STOECAB233

SYRUP RACK BASE PANEL

Attaches the bottom of the inner and side
panels.

10 STOECAB204R

SYRUP RACK RIGHT PANEL

Holds outer syrup rails.

11 STOEFAS2024

8-32 X 1/4" PAN HEAD SCREWS

Fastens pump brackets and pumps and
other cabinet parts.

12 STOECAB205A

ACCESSORY MOUNTING
BRACKET-A

Secures Accessory Mounting Bracket to
cabinet base.

13 STOECAB205CTP

ACCESSORY MOUNTING
BRACKET – CTP DLX

Secures pump cable to cabinet base.

14 STOEMIS3192

LOCKING HOLE PULUG

Closes up the extra opening in the mounting
plate.

15 STOEMIS3217

OPEN-CLOSE BUSHING 5/8”

Protects the pump harness cable.

16 STOEELE932DLX

PUMP & SANITIZER CABLE
HARNESS – CTP DLX

Provides power to the syrup and sanitizer
pumps.

17 STOESAN748

PERISTALTIC SANITIZER PUMP

Pumps sanitizer solution to flush tube and
sanitizer line.

18 STOESYR307

PERISTALTIC SYRUP PUMP –
SOFT SERVE

Pumps syrup from flavor bags into flavor
lines.

19 STOECAB255

PUMP BRACKET

Holds pumps.

20 STOESYR927

INTERNAL 9-TUBE ASSEMBLY

Transports syrup from bags to the 9-Tube
Assembly.

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

















































































Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Operator'S Manual

Search results

Summary of Contents for Stoelting Flavor Burst STL-80SS-DLX

Reviews:

Related manuals for Stoelting Flavor Burst STL-80SS-DLX

Brands by name

Popular brands